Hünnebeck's CS 240 L climbing scaffold is a crane-mounted mobile scaffold used both as a support scaffold in accordance with DIN 4421 for supporting wall formwork and as a working and protective scaffold in accordance with DIN 4420 Part 1 for reinforcement, concrete, and curing work. The steel structure is fully hot-dip galvanized. The project-specific assembly of scaffold units ensures a high degree of adaptability to specific structures. The wall formworks are connected to the bracket scaffold to form complete, crane-movable units. A retraction device on the CS 240 L allows the formwork to be lowered by up to 83 cm, depending on the formwork type. A tilting device allows for the formwork to be folded down. Any required concrete surface can be achieved using either frame formwork or timber-beam wall formwork. Depending on the scaffold width, it can be used at heights greater than 100 m above ground level and allows a maximum formwork height of 5.40 m. Offered here are:One main platform – 5,0 m wide – consisting of two brackets  Formwork and pouring height is 3.9m A leg platform  Rollback & Formwork Support Necessary accessories. pos. item No. description item       Total 1 600563 SCREW SET CS 240 2 2 2488 Half Coupler 48/M20x30 W.A.F. 22/ W.A.F. 30 8 3 2525 Swivel coupler 48/48 waf22 3 4 169078 TUBO d.48.3/3.25 L=400cm EP zinc 5 5 452053 WALER SPANNER 18 6 20492 TIE NUT 85 18 7 503919 STEEL WALER F 196 6 8 600378 WORKING PLATFORM BEAM CPL. 2 9 600320 VERTICAL BEAM, CPL. 2 10 600311 GUARD RAIL POST, CPL. 2 11 600304 DIAGONAL, CPL. 2 12 600563 SCREW SET CS 240 2 13 600390 WIND LOAD SEC. DEVICE, CPL. 2 14 600368 U 120 FORMWORK BEAM 370 CPL. 2 15 600295 SPINDLE 2 16 600344 LEVELLING ADAPTOR CPL. 2 17 600327 MOVE-OFF CARRIAGE CSL, CPL. 2 18 600365 DETACHABLE ADJUSTING UNIT 2 19 600313 VERTICAL EXTENSION BEAM, CPL. 2 20 600309 SUSPENSION PROFILE, CPL. 2 21 600310 EXTENSION SUSP. PROFILE CPL. 2 22 600306 TRAILING PLATFORM, CPL. 2 The following must be added on site: H20 beams for the platformsWooden decking for the platforms Additional edge protection Additional information you could find here: CS 240 climbing scaffold | Hünnebeck

The Loading Platform 5 800/290 helps to safely transport construction materials on construction sites. It is pre-assembled with minor adjustments possible both horizontally and vertically using the integrated crane attachment points. The Loading Platform is mounted on the outside of the building. The loading area protrudes from the building and offers a safe storage area of approx. 10.00 m2 which can be used to transport materials in and out of the building at floor level. Panel railings that prevent items and persons from falling off the platform ensure a safe working environment when working on the platform. The platform surface is made of slip-resistant corrugate plates.The Loading Platform is used to transport materials on site. It can be used in floors with a clearance of 1.90 m to 5.90 m. It can support up to 5,000 kg distributed across the entire surface.

The TOPMAX Table Lifting System is a modular construction system, which can be adapted quickly and flexibly to the requirements of the building.This system consists of a basic unit (basic frame with drive, control and three-part hoisting cage), single triangle lattice tower elements, pylon ties for the connection to the building, floor gates and connection cables. Load capacity: While movin: 1.685 kg While loading:2.370 kg

MCP 13 until 2009: 16340€  - for 10m of masts +2500 - for 20m masts +4930€ - for 30m masts +7120 - for 40m masts +9620€ + fencing 1600€ - + per complete landing door 1020€ 

The Alimak MC 450 is the next generation of strong, robust and quality mast climbing work platforms supplied by Alimak. This model offers the best ratio of performance and quality for global use in the light and medium range of applications. The Alimak MC 450 is used to transport people, their tools and materials to the working area to work safely and ergonomically as the machine can move between any level of the structure. Product Category: Mast Climbing Work Platforms Applications: Façade works on new build construction and renovation projects. Certifications: EN1495 Size: 1.2–2.2 x 4.2–30.2 m (W x L) Capacity: 750–5,500 kg Speed: 8–9.6 m/min. Voltage: 400 V / 50-60 Hz This offer consist of: Item CODE DESCRIPTION SINGLE FORMAT QTY DRIVE 661207 MC450 Base Unit 9YO 1 661220 Limit Ramp  2 661208 Access Gate 1 661209 Access Step, h’rail 1 661210 Mast Guard  1 661215 Control Panel with Handrail 1 VERTICAL 661256 Mast – Single Rack (A) 27 661255 Top Mast 1   Mast Bolts 112 PLATFORM   METSA BOARD NEW 1.5 6 661211 1500mm Deck 6   METSA BOARD NEW 0.8 OPTIONAL  661212 800mm Deck OPTIONAL   Deck Pin (DIA.36mm) 21   Deck Slides OPTIONAL 661227 1500mm Handrails 11 661228 800mm Handrails OPTIONAL   STANTION BKT OPTIONAL 661524 End Handrails 2   End Handrail Bracket 4 TIE 661823 3X2 DOUBLE 10 661216 Tie Bracket (Individual) 10   Drop Tube 10 661243 Tie Foot (MC450) 10 YOM: 2016  For more Information please visit: ALIMAK-MC-450-1554-EN-Nov-2021.pdf

The Alimak MC 450 is the next generation of strong, robust and quality mast climbing work platforms supplied by Alimak. This model offers the best ratio of performance and quality for global use in the light and medium range of applications. The Alimak MC 450 is used to transport people, their tools and materials to the working area to work safely and ergonomically as the machine can move between any level of the structure. Product Category: Mast Climbing Work Platforms Applications: Façade works on new build construction and renovation projects. Certifications: EN1495 Size: 1.2–2.2 x 4.2–30.2 m (W x L) Capacity: 750–5,500 kg Speed: 8–9.6 m/min. Voltage: 400 V / 50-60 Hz Item CODE DESCRIPTION TWIN FORMAT QTY DRIVE 661207 MC450 Base Unit 9YO 2 661220 Limit Ramp  4 661208 Access Gate 2 661209 Access Step, h’rail 1 661210 Mast Guard  2 661215 Control Panel with Handrail 1 VERTICAL 661256 Mast – Single Rack (A) 54 661255 Top Mast 2   Mast Bolts 224 PLATFORM   METSA BOARD NEW 1.5 12 661211 1500mm Deck 12   METSA BOARD NEW 0.8 OPTIONAL 661212 800mm Deck OPTIONAL   Deck Pin (DIA.36mm) 41   Deck Slides OPTIONAL 661227 1500mm Handrails 22 661228 800mm Handrails OPTIONAL   STANTION BKT OPTIONAL 661524 End Handrails 1   End Handrail Bracket 3 TIE 661823 3X2 DOUBLE 10 661216 Tie Bracket (Individual) 10   Drop Tube 10 661243 Tie Foot (MC450) 10 YOM: 2016 For more Information please visit:  ALIMAK-MC-450-1554-EN-Nov-2021.pdf

Personnel/Material Hoists for Construction  Commerical High Rise Power Generation Plants Refineries and Chemical Plants Shipyards Technical Datas: ELEVATOR Elevator drive                               Rack-and-pinion Maximum passengers               30 per car Total base unit weight                28,910 lbs (13,113kg) Capacity ...                                   6,000 lbs (2,721kg) per car   CAR/GATES Car weight                                    5,400 lbs (2,450kg) per car Maximum car speed                  300 ft/min (45.72 m/min) Interior dimensions                    12'4" L x 4'8" W x 7'2" H (3.76m L x 1.42m W x 2.18m H) per car Landing gates                               Swing type   TOWER Maximum tower height              900' (274.32m) consult factory for greater lifting heights Dimensions of tower section   56" L x 28" W x 60"H (1.42m L x .71m W x 1.52m H) Weight of tower section            485 lbs (220kg) Wall ties.                                        Adjustable strut 3" - 51" (.076 - 1.30m) Tie in intervals                             30' (9.14 m)   MOTOR/POWER Electrical Motor                           37.5 KVA, 460 VAC, 60 Hz, 3 phase per car Power required                            30 HP (22.5 kW) Motor control                               Full line voltage at start - variable frequency drive available Electrical outlet                           120 VAC Traveling cable                             6/6 - 2 ea- tower height plus 20' (12.19 m) required Base disconnect                         Circuit breaker or fuses in NEMA 4 enclosures Full load current                          37.5 Amps per car   BRAKES Brake                                              Electromechanical multiple disc, spring set Safety overspeed governor       Centrifugally actuated multiple friction disc brake Stopping distance accuracy    ± 6" (± 15.24cm) Brake torque                                 175 ft/lbs   COUNTERWEIGHT Weight of counterweight                5,400 lbs (2,450kg) per car Counterweight wire ropes              5/8" (1.59m) 6 x 25 XIP-IWRC Length of counterweight ropes     4 each tower height plus 40' (12.2m) required   Location is:                      Athens, NY 12015 - USA The sale price includes a complete overhaul, so that the device is ready for immediate use. The device can also be painted at the customer's request. This would be charged at an additional €4500/ 5000 US$.

Rugged, American-Built Personnel/Material Hoists For Construction       Commerical High Rise      Power Generation Plants      Refineries and Chemical Plants      Shipyards BASE UNIT DESCRIPTION The following components are included in the base unit package.  Completely assembled enclosed cars with overspeed governor and safety brake, motor and all drive components 20ft of tower for zero lifting height Limit and control switches Buffer springs Counterweight frame with necessary weights Two-rope cathead assembly with idler sheaves Motor and car control panel with constant-pressure, hand-levercontroller Power cable guide assembly Base fence enclosure SPECIFICATIONS Cage capacity,.                            8000 Ibs Per Car (3629 kg) Passenger, max.                          40 Per Car Cage dimensions (inside). Length                                            14'-0" ft .- in. (4,26 m) Width                                              5'-7" ft .- in. (1,70 m) Height                                            7'-2" ft .- in. (2,18 m) Cage speed                                  Low Speed Min. 141-Max. 148, ft./min.                                                          High Speed Min. 282-Max. 297, ft./min. Electric service                           62.5 KVA PER CAR        480 V-60Hz-3 PH Full load current.                         65 amps /Car Braking torque.                            2@-175, ft./lbs /Car Brakes                                            Electromechanical multiple disc Total weight of base unit lbs.    38,500 (17.464 kg) Cage weight,.                               5,800 Ea. Ibs (2630 kg) Weight of counterweight,.        9,000 Ea. Ibs (4082 kg) Tower height, max..                    900 ft (274 m) Tower sections,                           60x28x56 inches (152x71x142 cm) Tower section weights, Ibs.      485 (220 kg) Tower tie-in intervals, tt.            30 (9,14 m) Counterweight wire rope6x25XIP-IWRC                 3,-in. Counterweight wire rope length required               4 x tower ht. plus 40 ft. (12,19m) Traveling power cable (6/#6 Type W)                        1 x tower ht. plus 30 ft (9,14 m) Stationary power cable (6/#4 Type w)                      1 x tower ht. plus 30 it. (9,14 m)    Location is:                                Athens, NY 12015, USA The sale price includes a complete overhaul, so that the device is ready for immediate use. The device can also be painted at the customer's request. This would be charged at an additional €4,500.  

Personnel/Material Hoists for Construction    Commercial High Rise   Power Generation Plants   Refineries and Chemical Plants   Shipyards Technical Datas: CAGE CAPACITY, LBS.                                      7000 PER CAR (3175 kg) PASSENGER, MAX.                                            35 PER CAR CAGE FLOOR DIMENSIONS (INSIDE FLOOR)  LENGTH                                                               14'-5"  (4,39 m) WIDTH                                                                  5’-0" (1.524 m) HEIGHT                                                                8'-1" (2,44 m) SQUARE FEET AREA (INSIDE)                         72.5 SQ/FT (72,5 m²) CAGE SPEED,                                                      VARIABLE MAX. 300 FT./MIN (91 m/min) ELECTRIC SERVICE                                         277/480 V-60Hz-3 PH (can change transformer to          run on 400 volts 50 Hz) TRANSFORMER REQUIREMENTS                  150 KVA 208 DELTA 480 Y FULL LOAD CURRENT AMPS.                         125 AMPS. PER CAR TOTAL CAR WEIGHT, LBS.                                6,750 EACH (3061 kg) WEIGHT OF COUNTERWEIGHT, LBS.           8,000 / CAR (3628 kg) MAST SECTIONS, INCHES (LxWxH)              30.5 x 30.5 x 59.375  (77,5*77,5*151 cm) MAST SECTION WEIGHTS, LBS. (1/4" WALL)         390 LBS. (177 kg) COUNTERWEIGHT WIRE ROPE 6 x 25XIP-IWRC OR 6 x 19XIP-IWRC                         5/8 INCH (1,6 cm) COUNTERWEIGHT WIRE ROPE req.LENGTH        4 X TOWER HT. PLUS 40 FT. . (12,19m) TRAVELING POWER CABLE (6/#6 TYPE W)            1 X TOWER HT. PLUS 40 FT. . (12,19m)   Location is:                        Athens, NY 12015 The sale price includes a complete overhaul, so that the device is ready for immediate use. The device can also be painted at the customer's request. This would be charged at an additional €4500/ 5000 US$.